Release

Search

Appendices

Link copied to clipboard

  1. First, you need to know the SIP phone IP address. There are two ways to check this via the phone user interface:
    • Press the OK button in the idle screen.
    • Press Menu and select the Status tab.
  2. Specify the Yealink device’s IP address in your web browser’s address bar (e.g., http://1.2.3.4/).
  3. On the Account tab, go to the Register section. Select the phone line you wish to configure (named as Account) from the pull-down list in the Account field.
  4. Configure the registration parameters for the selected account in the corresponding fields:
    • Line Active – select Enabled here.
    • Label – the name of the account displayed on the LCD screen of your SIP phone (e.g., 17785551210).
    • Display Name – your identification (e.g., John Doe); this will be seen by the called party.
    • Register Name – ID that is used to authenticate your SIP account. This field is mandatory.
    • User Name – ID of your SIP account registered in PortaBilling.
    • Password – service password for your SIP account.
    • SIP server 1 section:
      • Server Host – PortaSIP IP address or hostname (e.g., 91.212.34.119).Account configuration and registrationIn the SIP server 2 section you can define the IP address of PortaSIP on the secondary site. If the main site becomes unavailable, the phone re-registers using this IP address.
  5. Click the Confirm button to update the SIP phone configuration.Status tab of a Sip phone

 

APPENDIX B. SJLabs softphone configuration for PortaSIP

Link copied to clipboard
  1. First, you need to install the SJPhone on your machine. Following installation, launch the SJPhone software. The following login screen will be displayed.

    Configure SJLabs Softphone

  2. Key in the account ID and password for PortaSIP and press OK. The SJPhone display should be similar to the one in the illustration below, showing the account balance in “Ready to call” state. The phone is now ready to be used.

    SJPhone Idle

  3. Right click on the softphone and press “Login…” to change or make corrections to the account/password.

APPENDIX C. Auto-provisioned IP phones and adapters

Link copied to clipboard

Currently the following IP devices can be auto-provisioned via PortaSwitch:

Phone model

Firmware version

AudioCodes

AudioCodes 405HD

AudioCodes 420HD

AudioCodes 430HD

AudioCodes 440HD

Calix

Calix 716GEI*

Calix 803G*

Calix 844E*

Calix 844G*

Calix 854G*

Cisco

Cisco ATA 186

ver. 2 and 3

Cisco SPA-122

Cisco SPA-504G

Cisco SPA-8000

Fanvil

Fanvil E52

Fanvil F52

Fanvil E58

Fanvil C58

Fanvil E62

Fanvil C62

Fanvil X3S

ver. 2.3.2.4600

Fanvil X4G

ver. 2.3.2.4600

Fanvil X5S

ver. 1.2.4

Fanvil X6

ver. 1.2.4

Fanvil C600

ver. 14.0.0.1.r2

Gigaset

Gigaset A580IP*

Gigaset C610IP*

Gigaset DX800A*

Grandstream

Grandstream DP715

Grandstream DP750 DECT base station with DP720 handsets

1.0.3.37

Grandstream GXP1160

Grandstream GXP1165

Grandstream GXP1400/1405

Grandstream GXP1450

Grandstream GXP1610

1.0.4.106

Grandstream GXP1615

1.0.4.106

Grandstream GXP1620

1.0.4.106

Grandstream GXP1625

1.0.4.106

Grandstream GXP1628

1.0.4.106

Grandstream GXP1630

1.0.4.106

Grandstream GXP1760

1.0.1.64

Grandstream GXP1780

1.0.1.64

Grandstream GXP1782

1.0.1.64

Grandstream GXP2130

Grandstream GXP2135

1.0.9.69

Grandstream GXP2140

Grandstream GXP2160

Grandstream GXP2170

1.0.9.69

Grandstream GXV3240

Grandstream GXV3275

Grandstream GXW400x

Grandstream GXW4216

1.0.5.28

Grandstream HT286

Grandstream HT486

Grandstream HT488

Grandstream HT496

Grandstream HT502

Grandstream HT503

Grandstream HT701

Grandstream HT702

Grandstream HT704

Grandstream HT802

1.0.5.11

Htek

Htek UC902P

2.0.4.4.25

Htek UC903

2.0.4.4.25

Htek UC912P

2.0.4.4.25

Htek UC923

2.0.4.4.25

Htek UC924

2.0.4.4.25

Htek UC926

2.0.4.4.25

Linksys

Linksys PAP2 (PAP2T)

Linksys RTP-300

Linksys/Sipura SPA-2102

Linksys SPA-941

Linksys SPA-942

Linksys SPA-921

Linksys SPA-922

Linksys SPA-3102

Linksys SPA-962

Linksys WRT54GP2

Motorola

Motorola CPEi

(Motorola NBBS Device Management Platform is required)

Newtec

Newtec AMC5001*

Newtec MDM2210Wifi*

Newtec MDM2500*

Newtec MDM2510*

Newtec MDM3100*

Newtec MDM3300*

Newtec MDM3310*

Newtec MDM5000*

Newtec MDM5010*

OneNetUno

OneNetUno ATA-171

Polycom

Polycom SoundPoint IP 331

Polycom SoundPoint IP 335

Polycom SoundPoint IP 550

Polycom SoundPoint IP 650

Polycom SoundPoint IP 670

Polycom SoundPoint IP 5000

Polycom SoundPoint IP 6000

RCA

RCA Telefield IP110

RCA Telefield IP160

RCA Telefield IP170

RCA Telefield IPX500

Siemens

Siemens A580IP

Sipura

Sipura 1001

Sipura 2000

Sipura 2002

Sipura 2100

Sipura 3000

Telefeld

Telefeld IP110*

Telefeld IP160*

Telefeld IP170*

Telefeld IPX500*

Thompson

Thomson TWG850 (only eMTA part)

Yealink

Yealink CP860

Yealink SIP-T19P

Yealink SIP-T19P E2

Yealink SIP-T20P

Yealink SIP-T21P

Yealink SIP-T21P E2

Yealink SIP-T22P

Yealink SIP-T23G

Yealink SIP-T23P

Yealink SIP-T26P

Yealink SIP-T27P

Yealink SIP-T28P

Yealink SIP-T29G

Yealink SIP-T32G

Yealink SIP-T38G

Yealink SIP-T41P

Yealink SIP-T42G

Yealink SIP-T46G

Yealink SIP-T48G

Yealink T19P E2

Yealink VP530 IP video phone

version 7x

Yealink W52P IP DECT phone

Yealink W80B DECT IP multi-cell base station

103.83.0.65

Zhone

Zhone GPONONT*

The devices marked with an * are also supported, but they have only been tested with MRs below MR85-0.

We are constantly working to extend the list of supported IP devices. If the IP phone you plan to use is not listed here, please contact us – it may already be scheduled for a future release, or we may include it at your request.

APPENDIX D. List of variables used in CPE profile configuration

Link copied to clipboard

CPE profiles describe configuration parameters required for provisioning an IP device automatically. Depending on the device type, the set of parameters will differ. Instead of defining them as set values, use variables that will be replaced with actual values during device provisioning.

The table below describes default variables used for IP device provisioning. They are global and can be used with any IP device type.

Variable

Description

$firstname

An account’s first name, taken from the First name field of the account’s Personal Info panel.

$midinit

An account’s middle name, taken from the Middle name field of the account’s Personal Info panel.

$lastname

An account’s last name, taken from the Last name field of the account’s Personal Info panel.

$id

Usually contains the account’s phone number. It is provisioned to the IP device as the username.

$h323_password

The account’s service password used to authenticate calls made from this IP device.

$i_account

The internal identifier of the account record. It is retrieved from the database.

$faxnum

An account’s fax number. It is taken from the account’s Address Info panel.

$ascii_key

The secret key used to encrypt the configuration files. It will be replaced by the IP device’s secret key value.

$i_env

The number of the billing environment. Configuration files are stored in separate directories per billing environment. Therefore, this number is typically included in the path to the configuration file with the parameters for IP device auto-provisioning.

Additionally, these variables are used in CPE profile configuration:

Variable

Description

$mac

The MAC address of the IP device. This is substituted by the MAC address taken from the device.

$i_customer

The unique ID of the customer record. It is retrieved from the database.

$i_passphrase

The unique identifier of a passphrase needed for password encryption. A passphrase is a constant value and is kept in secure storage.

$i_ua

The unique identifier of the IP device record.

$i_ua_link

The unique identifier of a port record for a particular IP device.

$i_ua_profile

The unique identifier for each version of the same CPE profile.

$ua_profile_id

The unique identifier for the CPE profile to be recognized in the system. It remains the same for all versions of the CPE profile.

$inventory_id

An ID that allows you to identify this IP device in the external system (e.g., your warehouse management application).

$manufacturer

The name of the IP device manufacturer.

$name

The name of the IP device in the CPE inventory.

$port

The IP device port to be used by a particular account.

$i_ua_type

The unique identifier of the IP device type. For example, if i_ua_type is 84 – then Yealink SIP-T23G with v8x firmware version is used.

$product

The model of the IP device of a particular type.

$version

The version of the IP device of a particular type.

$profile_name

The name of the CPE profile.

$config

The list of IP device port configurations.

$login

Login to the web self-care.

$password

Password to the web self-care.

$group_pickup

The prefix for answering a call to a huntgoup. This variable is applicable only to Gransdstream phones.

On this page

Release
What's new
Admin manuals
Handbooks
API
UI help
Search